 Sometimes when opening a session (Pro Tools LE 5.1), my Mix Window gets ...
|
| Sometimes when opening a session (Pro Tools LE 5.1), my Mix Window gets corrupted. It is shrunk to the upper left of the screen, even when maximized. |
In one case, this happened whenever an ADAT was connected, but powered OFF.
Powering ON the ADAT before opening a session resolved this behavior.
[Page View]
|
|
|
After installation of Soft SampleCell 3.1 LE, Pro Tools 5.3.2 doesn't ...
|
| After installation of Soft SampleCell 3.1 LE, Pro Tools 5.3.2 doesn't work properly anymore. |
Soft SampleCell 3.1 currently has versions for LE and HD on the installer. If you install the LE version on a Digi 002 system, it will corrupt the Digi 002 DSI and other Pro Tools extensions.
However, the Soft SampleCell 3.1 installer for HD will work fine with the Digi 002.
To get your system up and running again, first uninstall Soft SampleCell 3.1 and uninstall Pro Tools LE 5.3.2; then reinstall Pro Tool LE 5.3.2 followed by installing the HD version of Soft SampleCell 3.1.
The Soft SampleCell installer will be updated, in order to prevent this from happening in the future.
[Page View]
|
|
|
DAE error -6087 on a Digi 002 system on a G4 PCI graphics ("Yikes" model). ...
|
| DAE error -6087 on a Digi 002 system on a G4 PCI graphics ("Yikes" model). |
This error happens if you are using an incompatible PCI model G4 Macintosh. Only AGP model G4's are supported.
[Page View]
|
|
|
What is the fader resolution on the Digi 002?
|
| What is the fader resolution on the Digi 002? |
The fader resolution for the Digi 002 is 10-bit (1024 steps).
DUC Reference:
[Page View]
|
|
|
Sampletank and bundled 002 plugs-ins are not playing back. I can see level ...
|
| Sampletank and bundled 002 plugs-ins are not playing back. I can see level on the MIDI track but no level on the aux track. |
SampleTank uses RAM to playback samples. 320 MB of RAM is recommended to use Pro Tools LE 5.3.2 with SampleTank.
discovered by Digi Sales rep with Sony Vaio
[Page View]
|
|
|
When launching Pro Tools LE 5.3.1 (WinXP), the splash screen reads "Initializing ...
|
| When launching Pro Tools LE 5.3.1 (WinXP), the splash screen reads "Initializing MIDI" and then freezes. Upon restart Windows posts a "system has recovered from a severe error." |
This error can be caused by issues with QuickTime. Follow the instructions below for resolving this problem:
1) If Pro Tools LE 5.3.1 does not find QuickTime during initial installation, it will automatically take you to the Install Wizard. Allow the Pro Tools LE installer to continue and install QuickTime. Assuming it is successful, you will receive a Pro Tools LE 5.3.1 install completion message.
2) Restart the computer.
3) Before launching Pro Tools, open the Add/Remove Programs Control Panel and uninstall QuickTime. There will be 2 options, "Uninstall everything" or 'Uninstall." Choose "Uninstall everything." This will remove all software relating to QuickTime.
4) After successful uninstall of QuickTime, launch Pro Tools LE 5.3.1. you should be taken to authorization screen and enter your serial number.
%) Quit Pro Tools LE and proceed and reinstall QuickTime.
[Page View]
|
|
|
AVoption|XL functions are disabled when launching Pro Tools 5.1.3 or earlier ...
|
| AVoption|XL functions are disabled when launching Pro Tools 5.1.3 or earlier with AVoption XL. Avid System Test Pro reports "Digital Media Board has failed to initialize properly" at launch. |
This has been seen with Type III Meridien cards and Pro Tools/AVoption|XL 5.1.3 and earlier software. Digidesign began shipping Type III Meridien boards with AVoption XL systems around June of 2002. Previously, Type II cards were included.
To run AVoption|XL with a Mix or D24 system, it is required that the AVoption|XL 5.3.1 installer be run. Specifically, the file Meridien24p.dll 5.1.3r2 must be installed in the System Folder/DAE Folder/Video Engine Folder, and the file SCRP0101.abf must be installed to the System folder/DAE/Video Engine/SupportingFiles/Drivers folder. If an AVoption|XL 5.3.1 installer is not available, these files can be downloaded from www.digidesign.com.
These components are also backwards compatible with Meridien II cards so there is no harm in installing them if you think you may have an older card.
The version of Avid System Test that ships with AVoptionXL 5.0.1 - 5.3.1 does not support the Meridien type III cards and thus, fail to initialize the card at launch. An updated version of Avid System Test will be made available in the future.
Meridien Type III can be identified by its 12 LED's across the top or by the Avid part number 0030-03138-01. This card should work fine with Pro Tools HD based systems, although Avid System Test vDiags_8.1_CPR_d4 which ships with AVOption XL 5.3.1 does not recognize the Type III cards and fails to initialize at launch.
Meridien Type II can be identified by its 10 LED's across the top or by the Avid part number 0030-03007-01. This card should function with all D24, Mix, and HD based AVXL systems.
[Page View]
|
|
|
When launching Pro Tools 32T beta, the software quits and the following ...
|
| When launching Pro Tools 32T beta, the software quits and the following message is posted: "Pro Tools unexpectedly quit. Mac OS Type 2 error." |
In one case, the problem was caused due to a conflict with QuickTime Musical Instruments. Disabling QuickTime MI in the current OMS Studio Setup file solved the problem.
[Page View]
|
|
|
Selecting stored presets in an AudioSuite Plug-in while previewing will ...
|
| Selecting stored presets in an AudioSuite Plug-in while previewing will temporarily halt the preview; tapping fingers appear on-screen. |
The workaround is to select the new preset, at which point the preview will resume.
From the Read Me for Pro Tools LE v.5.3.2.
[Page View]
|
|
|
Digi 002 faders reset (a.k.a. slam) down to -inf when a change is made ...
|
| Digi 002 faders reset (a.k.a. slam) down to -inf when a change is made to OMS Setup while Pro Tools LE is running. This occurs even if Digi 002's Fader Mute is engaged prior to launching OMS Setup. |
A new version of firmware fixes this issue. It is available from:
http://www.digidesign.com/download/digi002.html
Making changes to the OMS setup, i.e. define an instrument, delete a defined instrument, or change the icon of a defined instrument, can cause this fader behavior.
[Page View]
|
|
|
